Stator Pick–Up Pulsar Coil For Polaris Ranger Scrambler Sportsman Honda

Stator Pick-Up Pulsar Coil For Polaris Ranger Scrambler Sportsman Honda

• All products shipped are tested
• One year limited warranty

Fits Models

• Polaris
  • ATP 500 2004 -2004
  • Big Boss 500 1998 -1999
  • Int’l Big Boss 2000 -2000
  • Int’l Big Boss 2002 -2002
  • Int’l Big Boss 500 1999 -1999
  • Int’l Big Boss 500 2001 -2001
  • Magnum 425 1998 -1998
  • Magnum 425 2×4 1995 -1997
  • Magnum 425 4×4 1995 -1997
  • Magnum 425 6×6 1996 -1997
  • Magnum 500 1999 -1999
  • Magnum 500 4×4 2000 -2001
  • Magnum 500 EB 2000 -2000
  • Magnum 500 HDS 2×4 2002 -2002
  • Magnum 500 HDS 4×4 2000 -2001
  • Magnum 500 HDS 4×4 2003 -2003
  • Magnum 500 RMK 2002 -2002
  • Magnum 500 VL HDS 2002 -2002
  • Scrambler 500 1997 -2000
  • Scrambler 500 2003 -2003
  • Scrambler 500 2×4 2001 -2002
  • Scrambler 500 4×4 2001 -2002
  • Sportsman 335 1999 -2000
  • Sportsman 400 2001 -2004
  • Sportsman 500 1996 -2000
  • Sportsman 500 2003 -2004
  • Sportsman 500 4×4 Carb 2001 -2002
  • Sportsman 500 6×6 Carb 2001 -2002
  • Sportsman 500 HO 2001 -2004
  • Worker 335 1999 -1999
  • Worker 500 1999 -1999
  • Worker 500 2001 -2002
  • Xpedition 425 2000 -2002
  • Xplorer 500 1997 -1997
  • Ranger 425 2003 -2003
  • Ranger 500 4×4 2004 -2004
  • Ranger 500 6×6 1999 -1999
  • Ranger 500 6×6 2004 -2004
  • Ranger 500 Series 10  2×4 2003 -2003
  • Ranger 500 Series 10  4×4 2003 -2003
  • Ranger 500 Series 10  6×6 2003 -2003
  • Ranger 500 Series 11 2004 -2004
• Honda
  • CR 125 R 1984 -1985
  • CR 250 R 1984 -1985
  • CR 500 R 1984 -1986
• Suzuki
  • DR 650 SE 1996 -2009
  • DR 650 SE 2011 -2016
  • RM 125 1989 -2001
  • RM 250 1986 -2001

Replaces OEM

• 3084974,
• 3085360,
• 3085561,
• 3086238,
• 3086821,
• 3086860,
• 3086984,
• 3087168,
• 31100-KA5-761,
• 31120-KA3-742,
• 31120-KA3-761,
• 31120-KA4-741,
• 31120-KA4-761,
• 31120-KA5-741,
• n32101-32E00,
• 32150-05D00,
• 32160-27C00,
• 32160-37E00,
• RM00103-R00,
• RM22843-R00

Technical Details

Number of wires : 2
Wires lenght : 3.5?
Pink/Red to White = 100 ohms+/-20%
Bracket center to center: 35 mm

Not following these instructions may result in damaging the part or other components on your vehicle.

• By using a small soldering iron weld the wires to the ones on your OEM wiring harness.
• Insulate your solders with heat shrink.
• Before attempting to start your vehicle, adjusting the air gap is necessary for certain models.
• Rotate the fly wheel by hand so the raised node is lined up with the pick up /pulsar coil and adjust as close as possible, but no less than 0.010’’.
• If no spark or erratic spark, switch the wires at the plug.

Part Application/Fitment

Interchanges/Cross References