Stator Pick–Up Pulsar Coil For Honda ATC 125 150 FL400R TRX 125–650

Stator Pick-Up Pulsar Coil For Honda ATC 125 150 FL400R TRX 125-650

• We offer a brand new pickup/pulser coil for you to repair your stator.
• Often unavailable from the OEM manufacture
• One year limited warranty
• All products shipped are tested

*All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.

Fits Models

• Honda ATC 125 M 1986 -1987
• ATC 200 X 1986 -1987
• ATC 250 SX 1985 -1987
• FL 400 R Pilot 1989 -1990
• TRX 125 Fourtrax 1987 -1988
• TRX 200 Fourtrax 1986 -1988
• TRX 200 Fourtrax 1990 -1996
• TRX 250 Fourtrax 1985 -1987
• TRX 250 Recon 1997 -2001
• TRX 250 Recon TE 2002 -2009
• TRX 250 Recon TE 2011 -2014
• TRX 250 Recon TM 2002 -2009
• TRX 250 Recon TM 2011 -2014
• TRX 250 Sportrax 2001 -2008
• TRX 250 X 1987 -1988
• TRX 250 X 1991 -1992
• TRX 250 X 2009 -2009
• TRX 250 X 2011 -2011
• TRX 250 X 2013 -2013
• TRX 300 Fourtrax 1988 -2000
• TRX 300 Fourtrax EX 1993 -2000
• TRX 300 Fourtrax FW 1988 -1992
• TRX 300 Sportrax 2001 -2008
• TRX 300 X 2009 -2009
• TRX 350 Fourtrax Foreman 1986 -1986
• TRX 350A Fourtrax Foreman 1987 -1989
• TRX 350D Fourtrax Foreman 1987 -1989
• TRX 350FE Rancher 2000 -2006
• TRX 350FM Rancher 2000 -2006
• TRX 350TE Rancher 2000 -2006
• TRX 350TM Rancher 2000 -2006
• TRX 400 Fourtrax Foreman 1995 -2003
• TRX 400 Rancher 2004 -2007
• TRX 450 Fourtrax Foreman ES 1998 -2001
• TRX 450 Fourtrax Foreman FE 2002 -2004
• TRX 450 Fourtrax Foreman FM 2002 -2004
• TRX 450 Fourtrax Foreman S 1998 -2004
• TRX 500 Fourtrax Foreman Rubicon 2001 -2003
• TRX 500 Fourtrax Foreman Rubicon 2007 -2009
• TRX 500 Fourtrax Foreman Rubicon FA 2004 -2006
• TRX 500 Fourtrax Foreman Rubicon FA 2011 -2014
• TRX 500 Fourtrax Foreman Rubicon FGA 2004 -2006
• TRX 500 Fourtrax Foreman Rubicon FPA 2012 -2014
• TRX 650 Rincon 2003 -2005

Replaces OEM

• 30300-HA0-003
• 30300-HA0-010
• 30300-HA0-013
• 30300-HA0-023
• 30300-HA0-033
• 30300-HA7-671

Technical Details

Number of pin : 1
Pickup : Pin to ground (metal bracket) = 350 ohms+/-20%
Bracket center to center: 36 mm
Not following these instructions may result in damaging the part or other components on your vehicle.

• By using a small soldering iron weld the wires to the ones on your OEM wiring harness.
• Insulate your solders with heat shrink.
• Before attempting to start your vehicle, adjusting the air gap is necessary for certain models.
• Rotate the fly wheel by hand so the raised node is lined up with the pick up /pulsar coil and adjust as close as possible, but no less than 0.010’’.
• If no spark or erratic spark, switch the wires at the plug.

Part Application/Fitment

Interchanges/Cross References